paint-line-toolkit
Server Configuration
Describes the environment variables required to run the server.
| Name | Required | Description | Default |
|---|---|---|---|
No arguments | |||
Instructions
Guidance the server publishes about itself, which clients place ahead of the tool catalog so the model reads it before choosing anything.
Preliminary sizing calculations for industrial finishing lines (paint/powder booths, cure ovens, air make-up units, conveyors). Use these tools for every number instead of estimating. The toolkit contains only physics and code-cited relationships: every design value (velocities, margins, efficiencies, allowances, geometry) is an INPUT. Never invent those values: ask the user for them, use osha_g10_velocity for liquid spray booths, or call suggest_design_basis, which works only if a private SizingAdvisor plug-in is installed. Units are imperial and named in every field; results also give SI. Pass the assumptions and warnings that matter on to the user. Preliminary sizing aid only. This toolkit implements public, textbook and code-cited relationships; every design value (velocities, margins, efficiencies, allowances, geometry) is supplied by the user. Results are NOT a substitute for equipment-vendor engineering, a licensed engineer's design, or review by the authority having jurisdiction (AHJ) against the code editions in force (e.g. NFPA 33, NFPA 86, OSHA 29 CFR 1910.94/1910.107, local fire and gas codes).
Capabilities
Features and capabilities supported by this server
Protocol revision2025-11-25
| Capability | Details |
|---|---|
| tools | {
"listChanged": false
} |
| prompts | {
"listChanged": false
} |
| resources | {
"subscribe": false,
"listChanged": false
} |
| experimental | {} |
Tools
Functions exposed to the LLM to take actions
| Name | Description |
|---|---|
| osha_g10_velocityB | Minimum maintained air velocity into a liquid spray booth, from OSHA 29 CFR 1910.94(c)(6) Table G-10. There is no public table for powder booths: ask the user for the vendor's value. |
| booth_exhaust_airflowC | Booth exhaust airflow Q [cfm] = area [ft²] × velocity [fpm]. |
| amu_sizingC | Air make-up unit: make-up cfm and burner input, BTU/h = 1.08 × cfm × ΔT (standard air). |
| oven_dwell_checkC | Cure-oven dwell = path length ÷ line speed, checked against heat-up + time at temperature. |
| oven_heat_loadC | Steady-state cure-oven heat balance: product + hangers + chain + exhaust + wall losses. |
| nfpa86_solvent_ventilationA | NFPA 86 screening value for oven safety ventilation: 10,000 scf per gallon of solvent, in scfm. |
| conveyor_throughputB | Parts/hour = speed × 60 ÷ pitch × parts per carrier × loading efficiency. |
| conveyor_required_speedC | Line speed (fpm) required for a target production rate. |
| hook_load_checkC | Carrier check: (part + hanger) × parts per carrier × design factor vs rated load. |
| index_cycleC | Indexing conveyor: cycle time, move time and dwell available per station. |
| part_clearance_checkC | Hung part cross-section vs a booth/oven silhouette or working opening. |
| building_clearance_checkC | Equipment top vs bottom of truss, and exhaust stack discharge height vs roof. |
| size_lineA | Preliminary sizing of a whole finishing line (conveyor, booth, oven, AMU, clearances). Needs the sizing request AND a complete design basis; ask the user for any value you lack. |
| suggest_design_basisA | Ask an installed SizingAdvisor plug-in for a design basis. The public package ships none, so this normally fails with 'not included': then ask the user for the design values. |
| list_referencesC | Codes, standards and references cited by the toolkit. |
Prompts
Interactive templates invoked by user choice
| Name | Description |
|---|---|
No prompts | |
Resources
Contextual data attached and managed by the client
| Name | Description |
|---|---|
No resources | |
TDQS
Scored across 15 tools
Most tools target clearly separate calculations: AMU sizing, booth airflow, oven heat load, conveyor throughput/speed, hook load, clearances, and code checks. The main ambiguity is between size_line and the individual sizing tools, though size_line is described as whole-line preliminary sizing. part_clearance_check and building_clearance_check could be momentarily confused but operate on different objects.
All names use snake_case consistently. Most are noun-based calculation labels (amu_sizing, conveyor_throughput, oven_heat_load), while a few are verb-led commands (size_line, suggest_design_basis, list_references); this is a minor deviation but still predictable.
Fifteen tools is well within a reasonable range for a specialized engineering toolkit. Each tool covers a distinct calculation or support function, and none appears redundant or filler.
The surface covers the core paint-line sizing workflow: conveyor, booth exhaust, OSHA/NFPA checks, oven dwell and heat load, AMU, hook/part/building clearances, whole-line sizing, and references. Minor domain gaps remain, such as duct/fan sizing, cooling or flash-off zones, and emissions beyond NFPA screening, but agents can work around them.